Cable tie guns: Manual or automatic cable tie guns for your applications!
With cable tie guns from HellermannTyton you hold all the advantages.
Assembly and installation tasks are becoming ever more complicated, which is why specialised cable tie guns are becoming increasingly important. No matter whether manual cable tie guns or automatic cable tie guns are involved, from the cable tie gun through hot-air guns to bundling systems, these cable tie guns have to fulfil quite specific tasks, which they also – depending on the production environment – have to fulfil under quite specific conditions.
For instance, a cable tie gun must even have to be usable in areas which are hard to reach, while other cable tie guns have to be able to operate during field operations without any access to electricity. To this are added the demands of modern serial production, meaning that, for example, attention already has to be paid while developing cable tie guns to ensuring that during long-term use, the operation of the cable tie gun is reliable and does not place excessive demands on the user.
HellermannTyton provides over 60,000 solutions covering all aspects of cables. All cable tie guns from HellermannTyton are subjected to strict tests and are tested for as long as it takes until every single cable tie gun meets the highest quality demands.
The user can, however, not just rely on the quality of the cable tie guns on offer. Whenever sector-specific reasons require it, HellermannTyton also provides support during the installation and use-testing of its cable tie guns on site. In this way, if a cable tie gun should ever not fulfil the exceptional requirements of a customer, then any adjustments which might be required can be undertaken immediately under close joint agreement or new cable tie guns can even be developed. So as to be able to provide this service, the world-wide development sites of HellermannTyton have facilities for developing, modifying and testing cable tie guns, ranging from the smallest cable tie gun right up to automatic bundling systems.
By choosing cable tie guns from HellermannTyton, series production managers, technicians, installers and users are deciding in favour of quality, effectiveness and productivity. Or, to put it another way – for advantages you can feel!
HellermannTyton is a global manufacturer who offers high performance fastening, connecting, routing, protecting, and identifying solutions to diverse markets. For our customers we develop market solutions that uniquely meet an industry's needs - solving an application requirement, saving installation and component costs, and improving the quality of the end product - no matter what your industry:
Electrically operated, automatic cable tie guns for use in the production of high-volume. Various tool versions are available for different applications. Waste-free "endless" bundle system ATS3080, fasteners for ATS3080, electrical cable tie gun AT2000 for bundling cable ties of series T18RA. The automatic cable tie guns "Autotool" are electrically powered Tools and fully automatic for processing cable ties in various applications. The automatic cable tie gun Autotool 2000 can bundle up to a diameter of 20 mm and the waste-free cable tie gun AutotoolSystem3080 a max. diameter of 80 mm.
Manual processing and pneumatic tools for plastic and metal ties. Plastic tools for installation. Rugged design metal tools and ergonomic mould plastic tools with adjustable tension for ambitious application with highest quality standard.
Application tooling for identification
Helafix HCT tools are ideal for cleanly cutting Helafix HCR carrier strips as well as punching out the securing holes.
Application tooling for non shrinkable tubing
Three-Prong tools to expand and apply elastomeric sleeves used for electrical insulation, mechanical protection and colour marking.
ASNP and MSNP snapper tools for safe and efficient fixing of snapper.
Automatic cable tie guns AT2000 / ATS3080 Efficient bundling for many applications
The two electrically operated cable tie guns are - due to its reliability, the simple handling and the flexibility - ideal for processing large numbers of cable ties in different application areas. Within seconds, bindings can be generated up to a diameter of 80mm for bundling and fixing.
Both automatic cable tie guns are manufactured by HellermannTyton, allowing a smooth procedure during repair, service issues and questions.
With an overhead dispenser or a bench mount kit system the automatic cable tie guns can be used stationary, mobile or integrated into a fully automated production line. It is also possible to use various clips and fixings.
Automatic cable tie gun AT2000 Automatic bundling up to a diameter of 20mm
The electrically powered cable tie gun Autotool 2000 CPK has been designed to speed up the binding process. During the cycle time of just 0.8 seconds, the steps bundling, threading, tensioning and cutting are performed automatically by pressing a button - quickly and with consistent quality. The waste is collected in a waste box, therefore, no cable tie waste can fall on the ground or into the production plant.
Especially in applications with high quality standards, e.g. in the cable assembly, Automotive, industrial- and packaging sector or in the white goods industry streamlines the automatic cable tie gun Autotool 2000 time-consuming and labour-intensive operations.
It can be processed bands with 50 cable ties or reels with a capacity of 3.500 cable ties.
Automatic cable tie gun ATS3080 Waste-free bundlings in seconds
The automatic cable tie gun ATS3080 is an outstanding innovation in bundling systems.
The outside serrated strap and closures are each supplied on "endless reels" so you get absolutely fully automated, waste-free bindings.
The automation of bindings allows efficient manufacturing of high quantities and cost-optimizing in a consistent workflow.
At the automatic cable tie gun ATS3080 the bundle diameter is detected automatically. This allows a flush cut off of the bindings and a optimised material utilisation is guaranteed.
Manual cable tie gun for plastic housing
Cable tie gun MK7 up to 4.8 mm strap width
The cable tie gun MK7 with its ergonomic design can be used anywhere. The casing is made of glass fibre reinforced polyester making it extraordinarily light. The MK7 cable tie gun is a state of the art tool for applying HellermannTyton cable ties up to a width of 4.8 mm.
The MK7 cable tie gun has a three level preset tension device for quick adjustment. Further adjustment is possible within each level. MIL approved. The MK7 cable tie gun is used by harness makers. Based on the US Military Specification (MIL) and the German Military Specification (VG) the cable tie gun MK7 is also used to apply cable ties in all military vehicles and aircrafts. An other range of application is the entire electrical installation e.g. in buildings or production plants.
For an especially high tensile strength we recommend our Cable tie gun MK7HT.
Manual cable tie gun metal housing Manual cable tie gun MK3SP up to 4.8 mm strap width
The manual cable tie gun MK3SP with its ergonomic design can be used anywhere. A tough and extremely low maintenance metal tool with an adjustable preset tension device for tensioning and automatically cutting HellermannTyton cable ties up to a width of 4.8mm.
Manual cable tie gun plastic housing Cable tie gun MK9 up to 13.5 mm strap width
The MK9 cable tie gun for applying HellermannTyton cable ties up to a width of 13.5mm is characterised by its very light weight and ergonomic design. Like the cable tie gun MK7, the housing is made of resilient and light weight glass fibre reinforced polyester.
The MK9 cable tie gun has two preset tension levels and a device for fine adjustment. MIL approved.
MK9 tool is used to apply bigger cable ties as they are used in trucks and busses. MIL and VG certification allows the use of the MK9 cable tie gun for military vehicle and aviation construction.
For an especially high tensile strength we recommend our Cable tie gun MK9HT.
Pneumatic cable tie guns plastic housing
Cable tie gun MK7P up to 4.8mm strap width
The MK7P pneumatic cable tie gun sets a new benchmark for the rational application of ties in the industrial production process. Enhanced technology significantly improves the application of cable ties.
Improved compressed air supply moves the tensioning piston faster than in comparable tools. Processing time is shortened and the volume of connecting ties applied is increased. At a time when cost implications are crucial this tool offers genuine potential for rationalisation.
Great attention was paid to ergonomic design in the development of this cable tie gun. The moulded handle prevents any slippage and eliminates operator fatigue. The housing of the cable tie gun is made of glass fibre reinforced plastic, which is a lightweight but very tough material that fully meets the high requirements found in industry today.
Applying the cable ties is remarkably easy: press the button and the cable tie is tensioned and then automatically cut off flush with the head. The smooth edge of the cut prevents injuries.
The cut off end of the tie is ejected automatically. Production breaks normally required to the cut off ties are thus eliminated.
The three level preset control is used to set the tool tension. Fine adjustment is then made with the wheel below the tension control. An optionally available safety cap prevents the tension setting being changed by accident. This is particularly important when bundling sensitive materials and represents an important aspect in maintaining process reliability.
This cable tie gun features a non slip, comfortable grip, soft touch trigger, and a one touch tensioning/cut off capability. The MK7P cable tie gun is very lightweight making it very easy for the operator to use on all cable ties from 2.5mm to 4.8mm wide.
The MK7P pneumatic cable tie gun sets a new benchmark for the rational application of ties in the industrial production process. Improved compressed air supply moves the tensioning piston faster than in comparable tools.
For automatic installation of cable ties up to 13.5mm wide we recommend the application tool MK9P.
Cable tie gun for KR-Series
Pneumatic cable tie gun for KR-Series Cable tie gun KR8PNSE
These cable tie guns are specially developed for processing HellermannTyton KR series cable ties with a width of 8.0mm. The KR8PNSE cable tie gun is a simple and easy to use tool which is ideal for applications where the volumes are too great for manual tooling.
The KR8PNSE pulls the strap tight, closes the head and cuts of the excess tail - all with a single push of the button.
Application tool KR8PNSE crimps the glass-fibre-reinforced locking pin of the KR seal and leads to plastic deformation of the tie ends. This produces a very proof permanent connection.
Manual cable tie guns for metal ties MBT- and MAT-Series
Cable tie gun MK9SST up to 13 mm strap width
With its lightweight, ergonomic design, the MK9SST cable tie gun is an ideal tool for applying the MBT series stainless steel cable ties. Although it is used for applying stainless steel cable ties, the MK9SST cable tie gun enables work to be carried out without operator fatigue.
For easier handling the tensioning is fully adjustable by means of a quick two level control with an additional fine setting. This feature means that damage to the bundled materials is easily avoided. The cable ties are automatically cut off flush with the head when the preset tensioning level has been reached.
Processing tools for heatshrink tubing, non-shrinkable tubing and carrier marking system
Gas powered Hot Air Tool E4500
The E4500 kit consists of a cordless gas heating gun with protective spring and a range of accessories including two different sized nozzles and a gas cartridge.
The hot air gun is a very convenient and compact tool, weighting only 760 g which operates with a gas cartridge (Type P444, Butane/Propanem or type 445, M.A.P.+ Butane+Propane).
It has an automatic piezo electric ignition and a valve controlled temperature setting.
The hot air gun can be operated on its stand for hands free use. The build in stand prevents the tool from tipping over.
The gas cartridge has a continuous burn time of approx. 1.5 hours. The E4500 can be used with no connection to electrical power supply and allows precise working in any position even in restricted spaces.
Three-Pronged for sleeves and grommets
Three-pronged pliers are used to fit sleeves of every type quickly and easily.
Helafix Tool HCT
HCT1 and HCT2 tools are ideal for cleanly cutting Helafix HCR carrier strips as well as punching out the securing holes.
The punching device is designed for HCR09 and HCR12 types of character carriers. For Helafix HCR06, HCR18 and HCR24 character carrier types, individual holes can be punched with both tools.
Both tools punch holes with a diameter of 2.5mm. To fix the carrier holders simply use the T18 range of cable ties, fixings or rivets.
EVO - The New Manual Processing Tool
With the EVO Cable Tie Gun, comfort and function are perfectly combined in a processing tool. The heart of the EVO is the innovative and patent-pending TLC technology (Tension / Lock / Cut).
Durable Stainless Steel Fixing Products
Whenever the environment is harsh the demand is for complete reliability, HellermannTyton offers a complete range of products for such conditions.